Cisco 15310-MA Průvodce řešením problémů stáhnout pdf (Strana 344)

4-36

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide, Release 9.0

78-18394-01

Chapter 4 Error Messages

EID-5019 The manual path trace mode for this equipment does not

support an expected string consisting of all null characters.

Please change the expected string or the path trace mode.

The path trace mode does not support

strings that consist of null characters. You

must either change the expected string or

the path trace mode.

EID-5020 Software activation is in progress. Provisioning is not allowed. Refer to the warning message text.

EID-5021 Software activation is in progress. {0} is not allowed. Refer to the error message text.

WID-5022 Warning: Ethergroup circuits are stateless (that is, always in

service).

The current state selection of {0} will be ignored.

Refer to the warning message text.

EID-5023 CTC cannot communicate with the node.

The operation failed.

CTC encountered a network

communication error. Connectivity

between CTC and the NE was disrupted,

either transiently or permanently.

EID-5024 The overhead circuit will not be upgraded. Refer to the error message text.

WID-5025 The path targeted for this switch request is already active. The

switch request can be applied, but traffic will not switch at this

time.

Refer to the warning message text.

EID-5026 An ONS 15600 cannot serve as the primary or secondary node

in a four-fiber {0} circuit. Please change your ring and/or node

selections so that an ONS 15600 is not chosen as the primary or

secondary node in this four-fiber {1} circuit.

Refer to the error message text.

WID-5027 The {0} Edit dialog box for the ring {1} has been closed due to

significant provisioning changes. These changes might only be

transitory, so you can reopen the {0} Edit dialog box to view

the updated state.

Re-open the BLSR/MS-SPRing edit

window to view the updated state of the

ring.

WID-5028 Warning: This operation should only be used to clean up rolls

that are stuck. It might also affect completeness of the circuit.

Is it OK to continue with the deletion?

Refer to the warning message text.

EID-5029 A software downgrade cannot be performed to the selected

version while an SSXC card is inserted in this shelf. Please

follow the steps to replace the SSXC with a CXC card before

continuing the software downgrade.

Refer to the error message text.

EID-5030 A software downgrade cannot be performed at the present time. Try the software downgrade later.

WID-5031 Canceling a software upgrade during a standby TSC clock

acquisition might result in a traffic outage.

Refer to the warning message text.

EID-5032 An error occurred while accepting the load. Refer to the error message text.

EID-5033 The profile could not be loaded.

An error occurred while decoding the characters.

CTC detected an error while decoding

characters and could not load the profile.

EID-5034 The profile could not be loaded.

An error occurred while trying to recognize the file format.

CTC detected an error and could not load

the profile.

EID-5035 The profile could not be loaded.

An error occurred while reading the file.

CTC could not read the file and is therefore

unable to load the profile.

Table 4-1 Error Messages (continued)

Error/Warning

ID Error/Warning Message Description

1 2 ... 339 340 341 342 343 344 345 346 347 348 349 ... 379 380

Komentáře k této Příručce

Žádné komentáře

Cisco 15310-MA Průvodce řešením problémů Strana 344

Komentáře k této Příručce

Související produkty a manuály pro Sítě Cisco 15310-MA