Cisco 15310-MA Průvodce řešením problémů stáhnout pdf (Strana 338)

4-30

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide, Release 9.0

78-18394-01

Chapter 4 Error Messages

EID-3328 An error occurred while applying changes to row {0}.

The value is out of range.

There was an error applying the changes to

the specified row. The value is out of range.

EID-3330 Unable to switch to the byte because an overhead channel is

present on this byte of the port.

Refer to the error message text.

EID-3331 An error occurred while applying changes to the row. Refer to the error message text.

EID-3334 Timing parameters on the protect port cannot be changed. You cannot change timing parameters on

protect port.

EID-3335 The port type cannot be changed because the SDH validation

check failed. Check if this port is part of a circuit, protection

group, SONET DCC, orderwire, or UNI-C interface.

Refer to the error message text.

EID-3336 An error occurred while reading a control mode value. The Control Mode must be retrieved.

EID-3337 An error occurred while setting a set point gain value. The Gain Set Point must be set.

EID-3338 An error occurred while reading a set-point gain value. The Gain Set Point must be retrieved.

EID-3339 An error occurred while setting a tilt calibration value. The tilt calibration must be set.

EID-3340 An error occurred while setting expected wavelength. The expected wavelength must be set.

EID-3341 An error occurred while reading expected wavelength. The expected wavelength must be retrieved.

EID-3342 An error occurred while reading actual wavelength. The actual wavelength must be retrieved.

EID-3343 An error occurred while reading actual band. The actual band must be retrieved.

EID-3344 An error occurred while reading expected band. The expected band must be retrieved.

EID-3345 An error occurred while setting expected band. The expected band must be set.

EID-3346 An error occurred while retrieving defaults from the node: {0}. There was an error retrieving defaults from

the specified node.

EID-3347 The file {0} cannot be loaded. CTC cannot load the specified file.

EID-3348 Properties cannot be loaded from the node. Refer to the error message text.

EID-3349 NE update properties cannot be saved to a file. Check your file system for space constraint

or any other problem.

EID-3350 NE update properties cannot be loaded from the node. Refer to the error message text.

EID-3351 The file {0} does not exist. The specified file does not exist.

EID-3352 An error occurred while setting a value at {0}. There was an error while setting the value at

the specified location.

EID-3353 No such interface is available. The interface specified is not present in

CTC.

EID-3354 The specified endpoint is in use. Select another endpoint that is not in use.

EID-3355 The specified endpoint is incompatible. Refer to the error message text.

EID-3357 The connections could not be calculated. Refer to the error message text.

EID-3358 An optical link model does not exist for the specified interface. Create an optical link model for the

interface, and proceed.

EID-3359 Optical parameters could not be set for the node. Refer to the error message text.

Table 4-1 Error Messages (continued)

Error/Warning

ID Error/Warning Message Description

1 2 ... 333 334 335 336 337 338 339 340 341 342 343 ... 379 380

Komentáře k této Příručce

Žádné komentáře

Cisco 15310-MA Průvodce řešením problémů Strana 338

Komentáře k této Příručce

Související produkty a manuály pro Sítě Cisco 15310-MA