Cisco 7600-ES20-GE3CXL-RF - Ethernet Services 20G Line Card Switch Uživatelský manuál Strana 254

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 398
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 253
700
Caveats for Cisco IOS Release 12.2(33)SRD through 12.2(33)SRD8
OL-10394-05 Rev. R0
Further Problem Description: After enabling ISAKMP debugging you will see in the first case:
ISAKMP:(68001): processing SIG payload. message ID = 0 ISAKMP:(68001): signature
invalid!
or possibly
ISAKMP (0:13005): FSM action returned error: 2
In the second case you will either see:
ISAKMP:(68001): processing ID payload. message ID = 0 ISAKMP (68001): ID payload
next-payload : 6 type : 9 Dist. name parsing failed protocol : 17 port : 500 length :
185 ISAKMP:(68001):: UNITY’s identity FQDN but no group info ISAKMP:(68001):: peer
matches *none* of the profiles
Or
00:03:18: ISAKMP (0:268435457): ID payload next-payload : 6 type : 9 Dist. name :
protocol : 17 port : 500 length : 73
(Notice the empty "Dist. name" field)
CSCsk43058
Symptoms: The interfaces on the Initial Wireless Services Module (WiSM) controllers are not
pingable.
Conditions: Occurs after upgrading a Supervisor Engine 720 to Cisco IOS Release 12.2(33)SXH.
The first interface assigned to the port channel shows as being active in the port channel and the
others show as suspended.
Workaround: All interfaces will come up in the port channel and connectivity will be restored if the
mls qos command is removed and then readded to the Supervisor Engine 720 global configuration.
CSCsk43745
Symptoms: The multicast switching path might be incorrectly displayed as fast- switched in the
output of the show ip interface tunnel x command.
Conditions: This symptom is observed when the tunnel-sequence datagrams command is enabled
on the tunnel interface, which should disable fast-switching.
Workaround: This is just a display issue. No workaround is needed.
CSCsk49705
Symptoms: The ip nat inside source static network command does not have the <cr> option.
Conditions: This symptom is observed on a Cisco 7200 router that is loaded with Cisco IOS
Release 12.4 or 12.4T.
Workaround: There is no workaround.
CSCsk54061
Symptoms: Memory allocation failed atm_vpivci_to_vc error occurs and device crashes.
Conditions: Occurs while configuring for ATM-AutoVC or with incoming ATM traffic.
Workaround: There is no workaround.
CSCsk54092
Symptoms: Link-state advertisement (LSA Type 3) may not get flushed from the database when the
route is suppose to be included as LSA Type 5.
Conditions: This symptom is observed when an LSA is changed from type 3 to type 5 on a Cisco
router. This is a timing problem between OSPF and BGP. Routes redistributed into OSPF are shown
as Type 3 LSAs when the sh ip ospf <process-id> database command is entered, even after the
removal of the network command under the router which is advertising these routes. These routes
are to be learned via Type 5 LSAs. This problem exists in all branches except Cisco IOS Release
12.2S.
Zobrazit stránku 253
1 2 ... 249 250 251 252 253 254 255 256 257 258 259 ... 397 398

Komentáře k této Příručce

Žádné komentáře