Cisco 2924C - Catalyst Switch Specifikace Strana 182
- Strana / 360
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 6 Configuring the System
Controlling IP Multicast Packets through CGMP
6-46
Catalyst 2900 Series XL and Catalyst 3500 Series XL Software Configuration Guide
78-6511-05
For CLI procedures, refer to the Cisco IOS Release 12.0 documentation on
Cisco.com for additional information and CLI procedures.
Controlling IP Multicast Packets through CGMP
CGMP reduces the unnecessary flooding of IP multicast packets by limiting the
transmission of these packets to CGMP clients that request them. The Fast Leave
feature accelerates the removal of unused CGMP groups. By default, CGMP is
enabled, and the Fast Leave feature is disabled.
End stations issue join messages to become part of a CGMP group and issue leave
messages to leave the group. The membership of these groups is managed by the
switch and by connected routers through the further exchange of CGMP
messages.
CGMP groups are maintained on a per-VLAN basis: a multicast IP address packet
can be forwarded to one list of ports in one VLAN and to a different list of ports
in another VLAN. When a CGMP group is added, it is added on a per-VLAN,
per-group basis. When a CGMP group is removed, it is only removed in a given
VLAN.
Note The same multicast MAC addresses cannot belong to both CGMP and
Multicast VLAN Registration (MVR) groups. CGMP does not dynamically
learn addresses that are MVR group members. If you want CGMP to learn an
address that is already an MVR group member, remove the address from the
MVR group.
Conversely, you cannot add an address to an MVR group if it is already a
CGMP group member. If you want an address that is already a CGMP group
member to be an MVR group member, remove the address from the CGMP
group, and then statically add it to the MVR group. For information about
MVR, see the “Configuring MVR” section on page 6-49.
- Catalyst 2900 Series XL and 1
- Catalyst 3500 Series XL 1
- Software Configuration Guide 1
- CONTENTS 3
- 1 Overview 1-1 4
- 5 Clustering Switches 5-1 6
- 6 Configuring the System 6-1 7
- Contents 10
- 78-6511-05 10
- 8 Configuring VLANs 8-1 11
- 9 Troubleshooting 9-1 13
- A System Error Messages A-1 14
- Audience 15
- Organization 17
- Conventions 18
- Related Publications 19
- Obtaining Documentation 20
- Ordering Documentation 21
- Documentation Feedback 21
- Cisco.com 22
- Technical Assistance Center 22
- Contacting TAC by Telephone 23
- Chapter 1 Overview 26
- Features 26
- Management Options 31
- Large Campus Configuration 42
- Hotel Network Configuration 44
- Multidwelling Configuration 47
- Getting Started with CMS 49
- Cluster Manager and VSM 51
- 10.1.126.45 52
- Cluster Tree 54
- Switch Images 55
- Redundant Power System LED 56
- Port Modes and LEDs 57
- 10/100 Ports 61
- 1000BASE-X Ports 61
- Menu Bars 62
- Cluster (VSM-specific) 63
- Move the cursor over 65
- Help Contents 65
- Port Pop-Up Menu 66
- Device Pop-Up Menu 67
- Monitoring 68
- Cluster is collapsed to a 70
- Connected cluster 70
- Status bar shows that 70
- Cluster View is displayed 70
- Switch202 71
- Topology 72
- Menu Bar 74
- CMS Window Components 79
- Host Name List 80
- Online Help 81
- Accessing CMS 83
- Saving Configuration Changes 85
- Management Software 86
- Where to Go Next 86
- Getting Started with the CLI 87
- Command Usage Basics 88
- • Change 89
- • Perform basic 89
- • Display 89
- Abbreviating Commands 90
- Redisplaying a Command 91
- Getting Help 91
- Note No space before tabbing 92
- Command-Line Error Messages 93
- Accessing the CLI 94
- General Switch Administration 97
- Switch Software Releases 98
- Console Port Access 99
- Telnet Access to the CLI 100
- HTTP Access to CMS 101
- Default Settings 105
- Device Management 106
- Flooding Control 109
- Network Redundancy 109
- Diagnostics 110
- Security 110
- Clustering Switches 113
- Understanding Switch Clusters 114
- Planning a Switch Cluster 116
- Standby Command Switches 117
- IP Addresses 120
- Passwords 120
- Host Names 122
- SNMP Community Strings 122
- Management VLAN 123
- Network Port 124
- NAT Commands 124
- Creating a Switch Cluster 125
- Verifying a Switch Cluster 131
- Displaying Link Information 132
- Command switch 135
- Trap 1, Trap 2, Trap 3 135
- Member 1 Member 2 Member 3 135
- SNMP Manager 135
- Configuring the System 137
- Changing IP Information 138
- DHCP Client Request Process 141
- Configuring the DHCP Server 142
- Configuring the TFTP Server 143
- Configuring the Relay Device 145
- Obtaining Configuration Files 146
- Example Configuration 148
- Changing the Password 151
- Configuring SNMP 154
- Entering Community Strings 155
- Adding Trap Managers 155
- Configuring CDP 158
- Configuring STP 160
- Disabling STP 161
- Enabling STP UplinkFast 166
- How CSUF Works 167
- Limitations 171
- Connecting the Stack Ports 171
- Changing the Switch Priority 175
- STP Port States 177
- Changing the Path Cost 179
- Changing the Port Priority 179
- Configuring STP Root Guard 180
- Managing the ARP Table 181
- Removing Multicast Groups 184
- Configuring MVR 185
- Setting MVR Parameters 189
- MAC Addresses and VLANs 192
- Adding Secure Addresses 194
- Removing Secure Addresses 195
- Adding Static Addresses 195
- Removing Static Addresses 196
- Configuring TACACS+ 197
- Network Services 201
- Starting TACACS+ Accounting 202
- Configuring the Switch Ports 205
- Configuring Flooding Controls 208
- Disabling Storm Control 209
- Enabling a Network Port 211
- Disabling a Network Port 212
- Configuring Protected Ports 217
- Enabling Port Security 218
- Disabling Port Security 219
- Enabling SPAN 220
- Disabling SPAN 220
- Configuring Voice Ports 221
- Different VLANs 224
- Configuring the LRE Ports 226
- Table 7-1 LRE Profiles 228
- LRE Ethernet Links 229
- Configuring VLANs 233
- Overview 234
- Management VLANs 236
- VLAN Membership Combinations 240
- Using VTP 244
- The VTP Domain 245
- Table 8-4 VTP Modes 246
- VTP Advertisements 247
- VTP Version 2 248
- VTP Pruning 249
- VTP Configuration Guidelines 250
- VTP Version 251
- Configuring VTP 252
- Configuring VTP Server Mode 253
- Configuring VTP Client Mode 254
- Enabling VTP Version 2 256
- Disabling VTP Version 2 257
- Enabling VTP Pruning 257
- Monitoring VTP 258
- VLANs in the VTP Database 259
- VLAN Configuration Guidelines 260
- Default VLAN Configuration 260
- Adding a VLAN 265
- Modifying a VLAN 266
- How VLAN Trunks Work 268
- Configuring a Trunk Port 270
- Disabling a Trunk Port 272
- How Class of Service Works 276
- Port Scheduling 277
- Load Sharing Using STP 278
- How the VMPS Works 284
- Dynamic Port VLAN Membership 285
- VMPS Configuration Guidelines 288
- Default VMPS Configuration 289
- Reconfirming VLAN Memberships 291
- Changing the Retry Count 292
- Troubleshooting 295
- Table 9-2 LRE Port Problems 298
- Troubleshooting CMS Sessions 299
- Chapter9 Troubleshooting 300
- Configuration Problems 303
- Recovery Procedures 307
- Step 7 Load any helper files: 317
- System Error Messages 321
- Table A-1 Facility Codes 322
- Chassis Message 325
- CMP Messages 325
- Environment Messages 326
- GigaStack Messages 327
- Link Message 328
- LRE Link Messages 328
- Module Message 329
- Port Security Messages 329
- RTD Messages 330
- Storm Control Messages 331
- Numerics 333
Související produkty a manuály pro Software Cisco 2924C - Catalyst Switch
Software Cisco 2955T 12 - Catalyst Switch Specifikace
(608 stránky)
(608 stránky)
Software Cisco Aironet 1200 Series Specifikace
(364 stránky)
(364 stránky)
Software Cisco ROUTER-SDM-CD Instalační příručka
(6 stránky)
(6 stránky)
Software Cisco ROUTER-SDM-CD Uživatelská příručka
(20 stránky)
(20 stránky)
Software Cisco HWIC Instalační příručka
(82 stránky)
(82 stránky)
Software Cisco Aironet 700 Series Specifikace
(402 stránky)
(402 stránky)
Software Cisco Catalyst 2900 Series XL Specifikace
(322 stránky)
(322 stránky)
Software Cisco ROUTER-SDM-CD Uživatelská příručka
(74 stránky)
(74 stránky)
Software Cisco IAD2431-1T1E1 Uživatelský manuál
(12 stránky)
(12 stránky)
Software Cisco UC520-24U-8FXO-K9 Uživatelský manuál
(18 stránky)
(18 stránky)
Software Cisco LightStream 1010 Specifikace
(89 stránky)
(89 stránky)
Software Cisco 3130 Specifikace
(107 stránky)
(107 stránky)
Software Cisco UC520-24U-8FXO-K9 Uživatelský manuál
(10 stránky)
(10 stránky)
Software Cisco WS-CBS3120X-S Specifikace
(100 stránky)
(100 stránky)
Rockwell Automation 1746-NI8 SLC 500 Analog Input Module Instructions Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Ausrüstung Rockwell Automation 1746-NI8 SLC 500 Analog Input Module Instructions.
Wir stellen 1 PDF-Handbücher Rockwell Automation 1746-NI8 SLC 500 Analog Input Module Instructions zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Rockwell automation 1746-NI8 SLC 500 Analog Input Module Instructions Bedienungsanleitung (20 Seiten)
Marke: Rockwell-automation | Kategorie: Equipment | Größe: 0.25 MB |
Weitere Produkte und Handbücher für Ausrüstung Rockwell Automation
| Modelle | Dokumententyp |
|---|---|
| 1753-L28BBB-M_P GuardPLC 1600 Controllers |
Bedienungsanleitung
Rockwell Automation 1753-L28BBB-M_P GuardPLC 1600 Controllers User Manual,
20 Seiten
|
| 1756-Mxxxx ControlLogix SERCOS interface Module In |
Bedienungsanleitung
Rockwell Automation 1756-Mxxxx ControlLogix SERCOS interface Module Installation Instructions User Manual,
20 Seiten
|
| 1746-HSCE2 Multi-Channel High-Speed Counter Instal |
Bedienungsanleitung
Rockwell Automation 1746-HSCE2 Multi-Channel High-Speed Counter Installation Instructions User Manual,
20 Seiten
|
| 1756-BATM ControlLogix Battery Module Installation |
Bedienungsanleitung
Rockwell Automation 1756-BATM ControlLogix Battery Module Installation Instructions User Manual,
32 Seiten
|
| 1762-IF4 MicroLogix Analog Input Module |
Bedienungsanleitung
Rockwell Automation 1762-IF4 MicroLogix Analog Input Module User Manual,
24 Seiten
|
| 1756-L53 Logix5553 Controller Installation Instruc |
Bedienungsanleitung
Rockwell Automation 1756-L53 Logix5553 Controller Installation Instructions User Manual,
18 Seiten
|
| 1784-PM16SE SoftLogix Motion Card Setup and Config |
Bedienungsanleitung
Rockwell Automation 1784-PM16SE SoftLogix Motion Card Setup and Configuration Manual User Manual,
451 Seiten
|
| 1775-S5_SR5,D17756.5.5 User Manual PLC-3 FAMILY I/ |
Bedienungsanleitung
Rockwell Automation 1775-S5_SR5,D17756.5.5 User Manual PLC-3 FAMILY I/0 User Manual,
181 Seiten
|
| 1771-IFF/A INSTL.INSTR FAST ANALOG INPUT |
Bedienungsanleitung
Rockwell Automation 1771-IFF/A INSTL.INSTR FAST ANALOG INPUT User Manual,
20 Seiten
|
| 1738-AENTR Armorpoint 2 Port Enet Adapter |
Bedienungsanleitung
Rockwell Automation 1738-AENTR Armorpoint 2 Port Enet Adapter User Manual,
24 Seiten
|
| 1738-ADNX ArmorPoint DeviceNet Adapters, Series A |
Bedienungsanleitung
Rockwell Automation 1738-ADNX ArmorPoint DeviceNet Adapters, Series A User Manual,
16 Seiten
|
| DeviceNet SEMINAR LAB EX |
Bedienungsanleitung
Rockwell Automation DeviceNet SEMINAR LAB EX User Manual,
71 Seiten
|
| 1792-IB8/B INSTL.INST ARMOR BLOCK 8 INPUT |
Bedienungsanleitung
Rockwell Automation 1792-IB8/B INSTL.INST ARMOR BLOCK 8 INPUT User Manual,
36 Seiten
|
| 1746-HSCE High-Speed Counter Module Installation I |
Bedienungsanleitung
Rockwell Automation 1746-HSCE High-Speed Counter Module Installation Instructions User Manual,
24 Seiten
|
| 1757-PIM ProcessLogix Pulse Input Module Installat |
Bedienungsanleitung
Rockwell Automation 1757-PIM ProcessLogix Pulse Input Module Installation User Manual,
16 Seiten
|
| 1794-OF4I FLEX I/O Isolated Analog Output Module I |
Bedienungsanleitung
Rockwell Automation 1794-OF4I FLEX I/O Isolated Analog Output Module Installation User Manual,
5 Seiten
|
| 1738-XXXX ArmorPoint 24V dc Output Modules, Series |
Bedienungsanleitung
Rockwell Automation 1738-XXXX ArmorPoint 24V dc Output Modules, Series A User Manual,
14 Seiten
|
| 1792D-CB18JP ArmorBlock MaXum I/O Cable Bases Devi |
Bedienungsanleitung
Rockwell Automation 1792D-CB18JP ArmorBlock MaXum I/O Cable Bases DeviceNet Powered Outputs Series B User Manual,
16 Seiten
|
| 1762-OX6I MicroLogix 1200 Relay Output Module |
Bedienungsanleitung
Rockwell Automation 1762-OX6I MicroLogix 1200 Relay Output Module User Manual,
16 Seiten
|
| 1784-PM02AE PCI 2 Axis Servo Card |
Bedienungsanleitung
Rockwell Automation 1784-PM02AE PCI 2 Axis Servo Card User Manual,
20 Seiten
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce