Cisco 7200 VXR Uživatelský manuál

Quick Start GuideCisco 7200 VXR Routers 1 Documentation and Resources2 Prepare for Installation3 Rack-Mount the Router4 Connect the Router to the Netw

103 Rack-Mount the RouterFigure 4 Attaching the Rack-Mount Brackets to the Front of the ChassisBrackets Front-Mounted—Chassis Protrudes from the Rack

11Figure 5 Attaching the Rack-Mount Brackets to the Front of the Chassis—Chassis RecessedBrackets Front-Mounted—Chassis Recessed in RackLocate the rac

12Figure 6 Installing the Rear Cable-Management Brackets with an NPE-G1 or NPE-G2 Installed—Router Front-MountedNPE-G1 and NPE-G2 Rear Cable-Managemen

13Figure 7 Attaching the Rack-Mount Brackets to the Rear of the Chassis—Front Protrudes from the RackBrackets Rear-Mounted—Front Protrudes from the Ra

14Figure 8 Attaching the Rack-Mount Brackets to the Rear of the Chassis—Front RecessedBrackets Rear-Mounted—Front Recessed in the RackStep 1 Locate th

15Figure 9 Installing the Rear Cable-Management Brackets with the NPE-G1 or NPE-G2—Router Rear-MountedNPE-G1 or NPE-G2 Rear Cable-Management Brackets

16NPE-G1 or NPE-G2 Optical Cable-Management Bracket Step 1 Loosen the left and right captive installation screws.Step 2 Hold the cable-management brac

17Figure 12 Installing the Chassis Ground ConnectionInstall the Chassis GroundNote The grounding lug and Phillips screws are not available from Cisco

184 Connect the Router to the NetworkFigure 13 Connecting the Console and Auxiliary Port CablesI/O Controller and NPE-G1 or NPE-G2 Console and Auxili

19Depending on the I/O controller installed in your Cisco 7200 VXR router, you may have a Gigabit Ethernet port, RJ-45 ports, or no Ethernet port. The

21 Documentation and ResourcesThis section contains information to help you prepare for installing the Cisco 7200 VXR router. It contains a list of o

20SFP and GBIC Interface Cables InstallationFor more information on cables, specifications, or product numbers, see the Cisco 7200 VXR Installation an

21Note Ensure that you connect the TX and RX ports on one end of the patch cord to the RX and TX ports (respectively) on the other end. Connect TX to

225 Start and Configure the RouterPower Cable ConnectionsCaution This unit might have more than one power cord. To reduce the risk of electric shock,

23Step 6 Plug the AC power supply cable into the AC power source. Repeat Step 1 through Step 6 for the second power supply (if present).Connect DC-Inp

24Note Make sure the entire stripped end of each lead is inserted all the way into its receptacle. If any exposed wire at the stripped end of a lead i

25Start the System and Perform a Basic ConfigurationStep 1 Check that all hardware parts and cables are securely attached to the chassis.Step 2 Check

26At any point you may enter a questions mark ‘?’ for help.Use ctrl-c to abort configuration dialog at any prompt.Default settings are in square brack

27 cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706Cisco Internetwork Operating System Softwar

28Enter enable secret: barneyThe enable password is used when there is no enable secret password and when using older software and some boot images.En

29 Configure IGRP routing? [yes]: Your IGRP autonomous system number [1]: 15Configure RIP routing? [no]:Configure CLNS? [no]: n Configure bri

3You can access the Cisco website at this URL:http://www.cisco.comYou can access international Cisco websites at this URL:http://www.cisco.com/public/

30Configure the Interface Transmission and Speed Modes for the NPE-G1 or NPE-G2Step 1 After changing the media type, configure the speed and transmiss

31Reset the Interface on the NPE-G1 or NPE-G2Should you have a problem with your NPE-G1 or NPE-G2 interface and wish to try and reset it, use the comm

32Configure Fast Ethernet InterfacesIn the following example, a Fast Ethernet interface in slot 2 is configured for a Fast Ethernet LAN using IP. Foll

33Step 3 If you are using AppleTalk on the interface, enter yes. Enter yes to configure for extended AppleTalk networks, and then enter the cable rang

34enable password bettyline vty 0 4password fredsnmp-server community publicip routingno vines routingipx routingappletalk routingno apollo routingno

35Check the Running Configuration SettingsTo check the value of the settings you have entered, enter the show running-config command at the Router# pr

366 After InstallationThis section contains hardware replacement instructions. The PC card or Flash memory card, CompactFlash Disk, Flash Disk, GBIC,

37Note If you have difficulty installing a processing engine or I/O controller in the lowest slot of a Cisco 7200 VXR router that is rack-mounted, rem

38Note If you have difficulty installing a processing engine or I/O controller in the lowest slot of a Cisco 7200 VXR router that is rack-mounted, rem

39To replace the CompactFlash Disk in the NPE-G1, see the “Prepare for Installation” section on page 6.Also see Using the Flash Disk at http://www.cis

4To see security advisories, security notices, and security responses as they are updated in real time, you can subscribe to the Product Security Inci

40Replace the SFP–NPE-G2Figure 22 Inserting an SFP Module into the NPE-G2 Gigabit Ethernet Port 0/1Use the following procedure to install an SFP modul

41To connect a Cisco USB Flash memory module or the Aladdin USB eToken Pro key to the NPE-G2 USB port, simply insert the module into the port as shown

42Step 3 With the port adapter halfway out of the slot, disconnect all cables from the port adapter. After disconnecting the cables, pull the port ada

43Figure 26 Removing the Port Adapter Jacket CardNote If you have difficulty removing the Port Adapter Jacket Card from the lowest slot of a Cisco 720

44Replace the Power SupplyFigure 27 Replacing the Power SupplyCaution Do not mix power supplies in Cisco 7200 VXR routers. In dual power supply config

457 Cisco Product Security OverviewCisco provides a free online Security Vulnerability Policy portal at this URL:http://www.cisco.com/en/US/products/

468 Obtaining Technical AssistanceCisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support &

47Definitions of Service Request SeverityTo ensure that all service requests are reported in a standard format, Cisco has established severity definit

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

5• iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenu

62 Prepare for InstallationWarningOnly trained and qualified personnel should install, replace, or service this equipment. Statement 1030WarningRead

7Prepare for Workbench or Tabletop InstallationFor a workbench or tabletop installation, verify the following before installing the router:• The route

8Figure 1 Installing a CompactFlash DiskStep 1 Turn the CompactFlash Disk so that the label is facing down. It is keyed and cannot be inserted incorre

9Figure 3 Inserting an SFP Module into the NPE-G2 Gigabit Ethernet Port 0/1Use the following procedure to install an SFP module in the NPE-G2:Step 1 A