Cisco ROUTER-SDM-CD Uživatelská příručka Strana 42
- Strana / 74
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 1 Cisco SDM Express
Supplementary Help
1-36
Cisco SDM Express 2.4 User’s Guide
OL-7141-05
The configuration that will be delivered to the router to enable and configure
logging is as follows, replacing <log buffer size> and <logging server ip
address> with the appropriate values that you enter into Cisco SDM Express:
logging console critical
logging trap debugging
logging buffered
<log buffer size>
logging
<logging server ip address>
Enable Unicast RPF on Outside Interfaces
Cisco SDM Express enables unicast Reverse Path Forwarding (RPF) on all
interfaces that connect to the Internet whenever possible. RPF is a feature that
causes the router to check the source address of any packet against the interface
through which the packet entered the router. If the input interface is not a feasible
path to the source address according to the routing table, the packet will be
dropped. This source address verification is used to defeat IP spoofing.
This works only when routing is symmetric. If the network is designed in such a
way that traffic from host A to host B may normally take a different path than
traffic from host B to host A, the check will always fail, and communication
between the two hosts will be impossible. This sort of asymmetric routing is
common in the Internet core. Ensure that your network does not use asymmetric
routing before enabling this feature.
In addition, unicast RPF can be enabled only when IP Cisco Express Forwarding
is enabled. Cisco SDM Express will check the router configuration to see if IP
Cisco Express Forwarding is enabled. If IP Cisco Express Forwarding is not
enabled, Cisco SDM Express will recommend that IP Cisco Express Forwarding
be enabled and will enable it if the recommendation is approved. If IP
Cisco Express Forwarding is not enabled, by Cisco SDM Express or otherwise,
unicast RPF will not be enabled.
To enable unicast RPF, the following configuration will be delivered to the router
for each interface that connects outside of the private network, replacing
<outside interface> with the interface identifier:
interface
<outside interface>
ip verify unicast reverse-path
- Customer Order Number: 1
- Text Part Number: OL-7141-05 1
- CONTENTS 3
- Contents 4
- Ol-7141-04 4
- Date and Time Properties 15 6
- Reset to Factory Defaults 16 6
- Feature Not Available 19 6
- Cisco SDM Express 7
- Router Provisioning 9
- Provision From USB Flash 11
- File Selection 12
- LAN Interface Configuration 13
- IP Address Field 14
- Subnet Mask Field 14
- Subnet Bits Field 14
- Wireless Parameters Fields 14
- DHCP Server Configuration 15
- Ending IP Address Field 16
- Domain Name Field 16
- Enable PPPoE Check Box 17
- Address Type List 17
- Authentication Type Check Box 18
- Username Field 18
- Password Field 18
- Confirm Password Field 18
- OL-7141-05 19
- Encapsulation List 20
- Virtual Path Identifier Field 20
- WAN Interface Selection 22
- Serial Connection 23
- DLCI Field 25
- LMI Type Field 25
- CNS Server Information 26
- Firewall Configuration 27
- Security Settings 28
- Encrypt Passwords Check Box 30
- Supplementary Help 31
- Cisco Network Services 32
- Disable PAD Service 34
- Disable CDP 37
- Disable IP Source Route 37
- Enable Netflow Switching 38
- Enable IP CEF 40
- Set Scheduler Interval 40
- Set Scheduler Allocate 40
- Set TCP Synwait Time 41
- Enable Logging 41
- <log buffer size> 42
- <outside interface> 42
- Disable IP Gratuitous ARPs 43
- Disable IP Redirects 43
- Disable IP Proxy ARP 43
- Disable IP Directed Broadcast 44
- Disable MOP Service 45
- Disable IP Unreachables 45
- Disable IP Mask Reply 45
- Set Banner 47
- Enable Telnet Settings 47
- Cisco SDM Express Buttons 49
- Apply Changes Button 50
- Discard Changes Button 50
- SDP Troubleshooting Tips 51
- Troubleshooting Tips 52
- Cisco SDM Express Edit Mode 53
- Internet (WAN) Fields 54
- Firewall Fields 54
- Basic Configuration 55
- Edit a Username 56
- Wireless 57
- No WAN Available 57
- Delete Connection 58
- Firewall 58
- Refresh Button 59
- Unable to Configure NAT 59
- • Web server 60
- • Email server 60
- Original Port 61
- Translated Port 61
- Protocol 61
- Enable Check Box 61
- Forwarding (Next Hop) Field 61
- Encrypt Passwords Checkbox 63
- Ping Option 64
- Telnet Option 64
- Cisco SDM Option 64
- Software Update Option 64
- Update SDM from Cisco.com 65
- Update SDM from Local PC 66
- Update SDM from CD 66
- Date and Time Properties 67
- Reset to Factory Defaults 68
- Microsoft Windows NT 70
- Microsoft Windows ME 70
- Microsoft Windows 2000 70
- Microsoft Windows XP 70
- Feature Not Available 71
- OL-7141-04 73
Související produkty a manuály pro Software Cisco ROUTER-SDM-CD
Software Cisco IAD2431-1T1E1 Uživatelský manuál
(12 stránky)
(12 stránky)
Software Cisco UC520-24U-8FXO-K9 Uživatelský manuál
(18 stránky)
(18 stránky)
Software Cisco LightStream 1010 Specifikace
(89 stránky)
(89 stránky)
Software Cisco 3130 Specifikace
(107 stránky)
(107 stránky)
Software Cisco UC520-24U-8FXO-K9 Uživatelský manuál
(10 stránky)
(10 stránky)
Software Cisco WS-CBS3120X-S Specifikace
(100 stránky)
(100 stránky)
Software Cisco ROUTER-SDM-CD Uživatelská příručka
(40 stránky)
(40 stránky)
Software Cisco ME 3400 Specifikace
(872 stránky)
(872 stránky)
Software Cisco SIEMENS HICOM 330E Uživatelský manuál
(73 stránky)
(73 stránky)
Software Cisco UC520W-8U-4FXO-K9 Uživatelský manuál
(14 stránky)
(14 stránky)
Software Cisco IE 2000 Specifikace
(336 stránky)
(336 stránky)
Software Cisco SIEMENS HICOM 330E Uživatelský manuál
(24 stránky)
(24 stránky)
Software Cisco LRE CPE Specifikace
(648 stránky)
(648 stránky)
Software Cisco Cisco Access Registrar 4.2 Specifikace
(636 stránky)
(636 stránky)
Rockwell Automation 1746-NI8 SLC 500 Analog Input Module Instructions Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Ausrüstung Rockwell Automation 1746-NI8 SLC 500 Analog Input Module Instructions.
Wir stellen 1 PDF-Handbücher Rockwell Automation 1746-NI8 SLC 500 Analog Input Module Instructions zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Rockwell automation 1746-NI8 SLC 500 Analog Input Module Instructions Bedienungsanleitung (20 Seiten)
Marke: Rockwell-automation | Kategorie: Equipment | Größe: 0.25 MB |
Weitere Produkte und Handbücher für Ausrüstung Rockwell Automation
| Modelle | Dokumententyp |
|---|---|
| 1753-L28BBB-M_P GuardPLC 1600 Controllers |
Bedienungsanleitung
Rockwell Automation 1753-L28BBB-M_P GuardPLC 1600 Controllers User Manual,
20 Seiten
|
| 1756-Mxxxx ControlLogix SERCOS interface Module In |
Bedienungsanleitung
Rockwell Automation 1756-Mxxxx ControlLogix SERCOS interface Module Installation Instructions User Manual,
20 Seiten
|
| 1746-HSCE2 Multi-Channel High-Speed Counter Instal |
Bedienungsanleitung
Rockwell Automation 1746-HSCE2 Multi-Channel High-Speed Counter Installation Instructions User Manual,
20 Seiten
|
| 1756-BATM ControlLogix Battery Module Installation |
Bedienungsanleitung
Rockwell Automation 1756-BATM ControlLogix Battery Module Installation Instructions User Manual,
32 Seiten
|
| 1762-IF4 MicroLogix Analog Input Module |
Bedienungsanleitung
Rockwell Automation 1762-IF4 MicroLogix Analog Input Module User Manual,
24 Seiten
|
| 1756-L53 Logix5553 Controller Installation Instruc |
Bedienungsanleitung
Rockwell Automation 1756-L53 Logix5553 Controller Installation Instructions User Manual,
18 Seiten
|
| 1784-PM16SE SoftLogix Motion Card Setup and Config |
Bedienungsanleitung
Rockwell Automation 1784-PM16SE SoftLogix Motion Card Setup and Configuration Manual User Manual,
451 Seiten
|
| 1775-S5_SR5,D17756.5.5 User Manual PLC-3 FAMILY I/ |
Bedienungsanleitung
Rockwell Automation 1775-S5_SR5,D17756.5.5 User Manual PLC-3 FAMILY I/0 User Manual,
181 Seiten
|
| 1771-IFF/A INSTL.INSTR FAST ANALOG INPUT |
Bedienungsanleitung
Rockwell Automation 1771-IFF/A INSTL.INSTR FAST ANALOG INPUT User Manual,
20 Seiten
|
| 1738-AENTR Armorpoint 2 Port Enet Adapter |
Bedienungsanleitung
Rockwell Automation 1738-AENTR Armorpoint 2 Port Enet Adapter User Manual,
24 Seiten
|
| 1738-ADNX ArmorPoint DeviceNet Adapters, Series A |
Bedienungsanleitung
Rockwell Automation 1738-ADNX ArmorPoint DeviceNet Adapters, Series A User Manual,
16 Seiten
|
| DeviceNet SEMINAR LAB EX |
Bedienungsanleitung
Rockwell Automation DeviceNet SEMINAR LAB EX User Manual,
71 Seiten
|
| 1792-IB8/B INSTL.INST ARMOR BLOCK 8 INPUT |
Bedienungsanleitung
Rockwell Automation 1792-IB8/B INSTL.INST ARMOR BLOCK 8 INPUT User Manual,
36 Seiten
|
| 1746-HSCE High-Speed Counter Module Installation I |
Bedienungsanleitung
Rockwell Automation 1746-HSCE High-Speed Counter Module Installation Instructions User Manual,
24 Seiten
|
| 1757-PIM ProcessLogix Pulse Input Module Installat |
Bedienungsanleitung
Rockwell Automation 1757-PIM ProcessLogix Pulse Input Module Installation User Manual,
16 Seiten
|
| 1794-OF4I FLEX I/O Isolated Analog Output Module I |
Bedienungsanleitung
Rockwell Automation 1794-OF4I FLEX I/O Isolated Analog Output Module Installation User Manual,
5 Seiten
|
| 1738-XXXX ArmorPoint 24V dc Output Modules, Series |
Bedienungsanleitung
Rockwell Automation 1738-XXXX ArmorPoint 24V dc Output Modules, Series A User Manual,
14 Seiten
|
| 1792D-CB18JP ArmorBlock MaXum I/O Cable Bases Devi |
Bedienungsanleitung
Rockwell Automation 1792D-CB18JP ArmorBlock MaXum I/O Cable Bases DeviceNet Powered Outputs Series B User Manual,
16 Seiten
|
| 1762-OX6I MicroLogix 1200 Relay Output Module |
Bedienungsanleitung
Rockwell Automation 1762-OX6I MicroLogix 1200 Relay Output Module User Manual,
16 Seiten
|
| 1784-PM02AE PCI 2 Axis Servo Card |
Bedienungsanleitung
Rockwell Automation 1784-PM02AE PCI 2 Axis Servo Card User Manual,
20 Seiten
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce