Cisco uBR10-LCP2-MC28C Specifikace stáhnout pdf (Strana 17)

Cisco uBR10-LCP2-MC16C/MC16E/MC16S Cable Interface Card for the Cisco uBR10012 Router

OL-2872-02

Removing and Replacing a Cisco uBR10-LCP2-MC16x Cable Interface Line Card

Unpacking a Cisco uBR10-LCP2-MC16x Cable Interface Line Card

Tip Make sure that you are using the ESD-preventive wrist strap.

Step 1 Open the shipping carton by cutting the packing tape along the flaps on the top of the box.

Step 2 Remove the Cisco uBR10-LCP2-MC16x cable interface line card from the packaging.

Step 3 Place the card on an antistatic surface.

Removing a Cisco uBR10-LCP2-MC16x Cable Interface Line Card

Tip To prevent alarms from activating, you must administratively shut down a cable interface line card before

hot swapping it. Refer to the Shutting Down and Restarting the Interface in the Cisco uBR7200 Series

Universal Broadband Router Software Configuration Guide at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/inter_c/icdoverv.htm

Otherwise, inform the network administrator that this portion of the network will be temporarily

interrupted. If the maintenance LED is on, you can remove the cable interface line card without affecting

systems operations.

Use the following procedure to remove an existing cable interface line card from the Cisco uBR10012

chassis.

Step 1 Attach an antistatic wrist strap to your wrist and to a bare metal, unpainted surface on the chassis or

frame.

Step 2 Face the back of the Cisco uBR10012 chassis. Clear enough interface and power cables to allow

sufficient space to work.

Step 3 If installing a new cable interface line card in a blank slot, remove the blank slot cover and discard it.

Otherwise, disconnect all coaxial cables from the cable interface line card being replaced or removed.

Step 4 Unscrew the top and bottom captive screws on the cable interface line card (Figure 7).

Step 5 Simultaneously pivot both ejector levers away from each other to disengage the cable interface line card

from the backplane (Figure 8).

Step 6 Slide the cable interface line card out of the slot and place it on an antistatic surface or in an antistatic

bag (Figure 9).

Step 7 If you are installing a new or replacement cable interface line card, continue with the next procedure.

Otherwise, install a blank cover over the slot and screw down its captive screws to conclude this

procedure.

Note For proper cooling and airflow, you must always install a blank cable interface line card cover in a blank

line card slot. Product order number Cisco UBR10-MC-COVER=.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 31 32

Komentáře k této Příručce

Žádné komentáře

Modely	Typ Dokumentu
KFC-W3010	Uživatelský manuál Kenwood KFC-W3010 User Manual [es] , 2 stránky
KFC-XW1224D	Uživatelský manuál Инструкция по эксплуатации Kenwood KFC-XW1224D, 2 stránky
KFC-S502P	Uživatelský manuál Инструкция по эксплуатации Kenwood KFC-S502P, 2 stránky
KSC-8803	Uživatelský manuál Kenwood KSC-8803 User Manual, 2 stránky
KSC-9903	Uživatelský manuál Kenwood KSC-9903 User Manual, 2 stránky

Cisco uBR10-LCP2-MC28C Specifikace Strana 17

Komentáře k této Příručce

Kenwood MFJ-286 manuály

Kenwood MFJ-286 Uživatelský manuál (1 strany)

Tabulka s obsahem

Další produkty a příručky pro Mikrofony Kenwood

Cisco uBR10-LCP2-MC28C Specifikace Strana 17

Komentáře k této Příručce

Související produkty a manuály pro Sítě Cisco uBR10-LCP2-MC28C

Kenwood MFJ-286 manuály

Kenwood MFJ-286 Uživatelský manuál (1 strany)

Tabulka s obsahem

Další produkty a příručky pro Mikrofony Kenwood