Cisco 2600-DC Series Instalační příručka stáhnout pdf (Strana 1)

Doc. No.

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

Cisco Systems, Inc.

Corporate Headquarters

Cisco 2600 Series Power Supply

Conﬁguration Note

Cisco Product Numbers:

PWR-2600-AC=, PWR-2600-DC=

This document describes how to replace the AC or DC power supply in a Cisco 2600 series router.

This document is intended for the power supply installer, who should be familiar with electronic

circuitry and wiring practices and have experience as an electronic or electromechanical technician.

Use this document in conjunction with the Cisco 2600 Series Hardware Installation Guide and the

Regulatory Compliance and Safety Information document for your router.

If you have questions or need help, refer to the section “Obtaining Service and Support” later in this

document.

This document contains the following sections:

• Safety Recommendations on page 2

• Overview of Cisco 2600 Series Power Supplies on page 4

• Tools and Equipment Required on page 6

• Removing the Cover on page 6

• Removing the Power Supply on page 8

• Installing the Power Supply on page 9

• Replacing the Cover on page 9

• Replacing Connections to the Router on page 10

• Troubleshooting on page 11

• Obtaining Service and Support on page 11

• Cisco Connection Online on page 12

• Ordering Documentation on page 12

78-5171-01

1 2 3 4 5 6 ... 13 14

Shrnutí obsahu

Strany 1 - Conﬁguration Note

Strany 2 - Safety Recommendations

10Replacing Connections to the RouterStep 5 Fasten the cover with the screws you set aside earlier.Step 6 Reinstall the chassis on a rack, wall, deskt

Strany 3 - Safety with Electricity

11TroubleshootingFigure 8 Cisco 2600 Series DC-Input Power Supply ConnectionsStep 3Turn ON the power switch. The power LED on the front panel of the

Strany 4

12Cisco Connection OnlineNote If you purchased your product from a reseller, you can access Cisco Connection Online(CCO) as a guest. CCO is Cisco Syst

Strany 5 - Cisco 2610

13Ordering DocumentationThe CD-ROM package is available as a single package or as an annual subscription. You can alsoaccess Cisco documentation on t

Strany 6 - Tools and Equipment Required

14Ordering Documentation

Strany 7 - Cisco 2600

2Safety RecommendationsSafety RecommendationsFollow these guidelines to ensure general safety:• Keep the chassis area clear and dust-free during and a

Strany 8 - Removing the Power Supply

3Safety with Electricity¡Advertencia! Este símbolo de aviso signiﬁca peligro. Existe riesgo para su integridad física.Antes de manipular cualquier e

Strany 9 - Replacing the Cover

4Overview of Cisco 2600 Series Power SuppliesFollow these guidelines when working on equipment powered by electricity:• Locate the room’s emergency po

Strany 10

5Overview of Cisco 2600 Series Power SuppliesFigure 1 Cisco 2600 Series AC Power SupplyFigure 2 Rear View of Cisco 2600 Series (Cisco 2610 Shown)Tabl

Strany 11 - Obtaining Service and Support

6Tools and Equipment RequiredTools and Equipment RequiredYou need the following tools and equipment to remove and install power supplies in Cisco 2600

Strany 12 - Ordering Documentation

7Removing the Cover(c) Use a screwdriver to remove the three power leads from the terminal block, in thefollowing order: negative, positive, then gro

Strany 13

8Removing the Power SupplyRemoving the Power SupplyThis section describes how to remove the internal power supply. Although the AC power supply isshow

Strany 14

9Installing the Power SupplyStep 3 Slide the power supply forward slightly in the chassis. This disengages the built-in hooksthat help secure the pow