78-20503-01 MX300 Wall Mount Installation Sheet | 2011 NOVEMBER | © 2011 Cisco Systems, Inc. All rights reserved.
Installing Cisco TelePresence MX300 - Wall Mount
1
Unpacking the MX300 box with the LCD video unit, Touch controller and accessories
4
Connecting the cables
2
Mounting the LCD video unit bracket
3
Mounting the bottom adapter
The MX300 delivery
The MX300 with a wall mount bracket is delivered in two
boxes with the following parts:
• Wall bracket, LCD video unit bracket, bottom adapter and
back cover. Screwdriver.
• LCD video unit, touch controller, microphones and cables.
Screws, screwdriver and gloves.
Manpower
Two people working together are required to mount the LCD
video unit to the wall.
Dimensions
Height (not including the camera): 840 mm / 33 in.
Width: 1290 mm / 51 in.
Depth (including brackets): 190 mm / 7.5 in.
Weight: 38 kg / 84 lb
Documentation
The user documentation for this product, including
compliance and safety information, is available on the Cisco
web site, http://www.cisco.com/go/telepresence/docs.
iii Move the LCD video unit bracket toward the
LCD video unit and align the four holes for the
screws.
Fasten the bracket to the LCD video unit
with the four screws that you removed in the
previous step (tool: hexagonal screwdriver).
Note: Always use the provided gloves when handling
the LCD video unit to avoid stains on the unit’s surface.
i Lift the LCD video unit carefully
out of the bottom tray and place
it gently face down on a steady,
soft surface. Two people working
together are required for this
operation.
CAUTION: Take care not to subject the camera for
any stress (turn it parallel to the LCD video unit).
ii Unscrew and remove the four pre-mounted screws
at the back of the LCD video unit (see illustration)
(tool: hexagonal screwdriver).
You will reuse these screws in the next step.
31 kg / 68 lb
i Remove the cable channel
lid to get access to the
holes for the screws.
ii Slide the bottom adapter into the
LCD video unit and fasten it with two
of the screws in the accessories box
(tool: hexagonal screwdriver).
Bottom adapter
LCD video unit
Cable channel lid
(for strain relief)
i Thread the cables up through the hole
in the bracket and connect them to the
LCD video unit.
The connectors are placed at the
rear side of the LCD video unit. See
illustration for details.
ii Snap on the cable channel lid for strain
relief.
Note: When you position the cables side
by side it is easier to snap on the lid.
i Cut the straps and lift off
the outer covering.
ii Remove the upper foam
protection.
Note: Leave the LCD
video unit in the bottom
tray for now.
iii Lift out the rectangular
box behind the LCD video
unit.
This box contains two
smaller boxes: One with
the Touch controller, and
one accessories box with
the microphones, cables,
screws and screwdriver.
Bottom tray
Outer
covering
LCD video
unit
Touch controller
with cable
Accessories box:
• Two microphones
• Power cable
• Presentation cable
(VGA to DVI-I;
stereo audio)
• Ethernet cable
• Four screws (two for
fastening the bottom
adapter; two spares)
• Hexagonal screwdriver
• Two pairs of gloves
LCD video unit connectors
Note: You will not have access to the
connectors after you have fastened the
LCD video unit to the wall.
Power
supply
Power
switch
For maintenance only
Touch controller
Local area
network (LAN)
PC audio input
PC video input
Audio line output
(cable not included)
Microphones
Reset factory settings
LCD video
unit bracket
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce