Cisco 3020 Uživatelský manuál Strana 1

Getting Started GuideCisco Catalyst Blade Switch 3020 for HP Getting Started GuideINCLUDING LICENSE AND WARRANTY1 Introduction2 Taking Out What You N

10 Before you run Express Setup, you must set up your switch module to communicate with a Hyperterminal program.Note The initial configuration assumes

11 Using Express Setup to Assign a VLAN 1 IP Address to the Switch ModuleUse these steps to assign an IP address to the VLAN 1 interface through Expre

12 Step 4 Press and hold the Mode button until the four LEDs next to the Mode button turn green. This takes approximately 3 seconds. Step 5 Release th

13 Figure 5 Connecting the Ethernet Cable from a PC to a Switch Module Ethernet PortCaution Do not connect the switch module to any device other than

14 Step 9 Enter the IP address 10.0.0.1 and press Enter.The Express Setup home page appears.Step 10 Go to “Completing the Express Setup Fields” sectio

15 After you install the switch module in the interconnect module bay, after approximately 2 minutes, the switch module automatically obtains an IP ad

16 Step 6 Click the IP address hyperlink for the switch module from the Management URL column to open a new browser window. The Device Manager window

17 The Express Setup page appears.Step 8 Go to “Completing the Express Setup Fields” section on page 17 to finish setting up the switch module using t

18 Step 2 (Optional) You can enter the Optional Settings information now or enter it later by using the device manager interface:–In the Host Name fie

19 Refreshing the PC IP AddressAfter you complete Express Setup, you should refresh the PC IP address:• For a dynamically assigned IP address, disconn

2 1 IntroductionThis guide provides instructions on how to install your Cisco Catalyst Blade Switch 3020 for HP—hereafter referred to as the switch m

20 3. Use the device manager to perform basic switch module configuration and monitoring. Refer to the device manager online help for more information

21 –No parity–1 stop bit–No flow control4. Use the CLI to enter commands to configure the switch module. See the software configuration guide and the

22 Troubleshooting Express SetupIf Express Setup does not run, or if the Express Setup page does not appear in your browser:• Did you verify that POST

23 Resetting the Switch ModuleThis section describes how to reset the switch module by rerunning Express Setup. These are reasons why you might want t

24 • Network interface cards• Troubleshooting tools• Field notices and security advisoriesFollow these steps:1. Open your browser, and go to http://ww

25 8 Obtaining DocumentationCisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain tech

26 Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m. (0800 to 1700) PDT by calling 1 866 463-3487 in the Uni

27 Reporting Security Problems in Cisco ProductsCisco is committed to delivering secure products. We test our products internally before we release th

28 11 Obtaining Technical AssistanceCisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support &a

29 For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in w

3 If the switch modules are ordered with the blade server, the switch modules are already installed. The unpacking procedure for the switch module app

30 • Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo merchandise. Visit Cisco Marketplace, the company

31 13 Hardware Warranty TermsThese sections describe the warranty terms for the switch:• If you purchased the Cisco Catalyst Blade Switch 3020 for HP

32 c. Click Go. The Cisco warranty page appears.d. Review the document online, or click the PDF icon to download and print the document in Adobe Porta

33 WARRANTY PROVIDED FOR THE HP PRODUCT, AND ALSO CONTAINS CERTAIN DISCLAIMERS AND LIMITATIONS OF LIABILITY BY HP, WHICH MATERIALLY IMPACT YOUR RIGHTS

34 Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is pr

35

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

4 The blade server includes a chassis management module, the Onboard Administrator. Each switch module connects internally to the Onboard Administrato

5 3 HP c-Class BladeSystem ArchitectureFigure 2 shows the rear view of the blade server, in which you install the switch module.Figure 2 Rear View of

6 Consider these prerequisites before installing your switch module:• Fill any unoccupied interconnect bays or any unoccupied power module bays in the

7 Follow these steps to install the switch module in the blade server:Step 1 If you have not already done so, touch the static-protective package that

8 Step 4 Ensure that the release latch on the switch module is in the open position (perpendicular to the module):Step 5 Slide the switch module into

9 Step 6 Push the release latch on the front of the switch module to the closed position. Switch Module IP AddressesIP addresses can be assigned to tw