Cisco 826 Uživatelský manuál stáhnout pdf

Password Recovery Procedure for the Cisco 806,

826, 827, 828, 831, 836, and 837 Series Routers

Document ID: 12065

Introduction

Prerequisites

Requirements

Components Used

Related Products

Conventions

Step−by−Step Procedure

Example of Password Recovery Procedure

NetPro Discussion Forums − Featured Conversations

Related Information

Introduction

This document describes how to recover the enable password and the enable secret passwords. These

passwords protect access to privileged EXEC and configuration modes. The enable password password can

be recovered, but the enable secret password is encrypted and must be replaced with a new password. Use the

procedure described in this document in order to replace the enable secret password.

Note: Refer to Password Recovery Procedure for the Cisco 801, 802, 803, 804, 805, 811, and 813 Series

Routers in order to recover a password on the Cisco 801, 802, 803, 804, 805, 811, and 813 Series Routers.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on these hardware versions:

Cisco 806 Series Router•

Cisco 826 Series Router•

Cisco 827 Series Router•

Cisco 828 Series Router•

Cisco 831 Series Router•

Cisco 836 Series Router•

Cisco 837 Series Router•

The information in this document was created from the devices in a specific lab environment. All of the

devices used in this document started with a cleared (default) configuration. If your network is live, make sure

that you understand the potential impact of any command.

Cisco − Password Recovery Procedure for the Cisco 806, 826, 827, 828, 831, 836, and 837 Series Routers

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Prerequisites

Password Recovery Procedure for the Cisco 806,826, 827, 828, 831, 836, and 837 Series RoutersDocument ID: 12065IntroductionPrerequisites Requirem

Strany 2 - Step−by−Step Procedure

Related ProductsRefer to Password Recovery Procedures for information on how to recover passwords for related products.ConventionsRefer to Cisco Techn

Strany 3

The router reboots, but ignores the saved configuration.Type no after each setup question, or press Ctrl−C in order to skip the initial setup procedur

Strany 4

Image text−base: 0x80008088, data−base: 0x80C524F8ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)Router uptime is 3 minutesSystem re

Strany 5

(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227−7013. cisco Systems, Inc. 170 West Tasman Drive San Jos

Strany 6

00:00:53: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/0, changed state to down00:00:53: %LINEPROTO−5−UPDOWN: Line protocol on Interface

Strany 7

System image file is "flash:c2600−is−mz.120−7.T"cisco 2611 (MPC860) processor (revision 0x202) with 26624K/6144K bytes of memory.Processor b

Strany 8 - Related Information

NetPro Discussion Forums − Featured Conversations for Router and IOS ArchitectureNetwork Infrastructure: LAN Routing and SwitchingNetwork Infrastructu

Komentáře k této Příručce

Žádné komentáře

Cisco 826 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Sítě Cisco 826. Cisco - Password Recovery Procedure for the Cisco 806, 826, 827 Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Sítě Cisco 826